Eye-catching vinyl-wrapped vehicles are becoming more and more common on our streets. And no wonder – these mobile billboards make millions of impressions a year and can be used for long-term or short-term promotions with the addition of a decal. Flexible and cost-effective, vinyl wrap advertising is catching on fast.
If you’re looking for a company capable of creating vehicle signs in Lewes, you’ll need to check out whether they have a dedicated vehicle wrapping team. Why? Because wrapping a vehicle so that there are no lines, bulges and wrinkles to spoil the integrity of the design is an art.
Why You Should Vinyl-Wrap Your Vehicles
Think of a vinyl wrap as like lightweight armour for your car. Properly laminated, it can last ten years, during which time your vehicle is protected from wear and tear and damage from the elements. Highly mouldable and stretchable, vinyl can make your car look immaculate and give a professional shine to your advertising campaigns. And when you want to change your branding or make your campaigns more responsive, you can either opt for a partial wrap and decals or start all over again with a full body wrap.
Measure for Size
Before you even think about ordering your vinyl wrap, you’ll need to measure up your vehicle or vehicles so you have a good estimate of how much vinyl you’ll need. Don’t skip this step – a vehicle left half finished because you didn’t order enough vinyl will create a really poor first impression.
The easiest calculation is to measure the length of your car, multiply by three and add an extra five metres. The best way to plan for how much vinyl you’ll need for a professional car wrap is to ask the professionals and work with them on creating a design that will take advantage of the particular bodywork of your company car or van fleet.
Clean It Up
Next you’ll need to clean like you’ve never cleaned before. Waxes and oils affect the adhesion of the vinyl, so it’s critical that these are stripped from the car body before wrapping can start. Get right into the wheel wells and under the hood, as these are areas that you don’t often see yet can compromise the effect of your body wrap if you don’t pay attention to them.
Then you’ll need to give the bodywork a thorough going-over with paint cleaner and alcohol to get rid of any traces of grease. Also pay attention to any rust or paint chips. Because vinyl stretches over your vehicle like a second skin, any obvious blemishes will stick out, so fill any chips and deal with those rust spots. The rule of thumb is if you can feel it, it will show up on the outside – and that includes dead bugs!
Plan It Out
Before a wrap is applied, an installer will size up the vehicle and make a start with the most awkward pieces like the bumpers or the bonnet. It can often be easier to detach mirrors and trim rather than spending a long time trying to work round them. It might take five minutes to remove them and make your life easier.
Never Over-Stretch
Each piece of the wrap is applied separately by removing the backing paper and then smoothing into place with a squeegee. Sounds simple? Far from it. Experienced wrappers will know just how far a wrap can be heated, stretched and repositioned, but over-stretching the vinyl is one of the easiest mistakes to make. Do that and you’ll thin out the glue, resulting in imperfect adhesion of the vinyl. You’ll also distort the pattern and affect the finish, whether it’s matte or glossy.
Cut It Out
A really good installer can trim away the excess while the vinyl is in position on your car. The easiest way to achieve a good result without the risk of cutting into the paintwork is to peel away the edges, trim the vinyl to fit, and reapply.
Where you’re dealing with creating accurate seams, a product like knifeless tape will allow you to overlap two pieces of vinyl over the tape and then pull away the Kevlar thread, which neatly and accurately slices away any unwanted vinyl for a seamless finish.
Don’t Forget the Post-Heat
If you’ve applied a partial wrap to flat areas like car doors and bonnets, where no stretching of the vinyl is required, you can skip this step. But if you’ve applied a full car vinyl wrap, including mirrors and bumpers, then it’s imperative that you apply a heat gun to those areas so your stretched vinyl doesn’t shrink back to its original state.
Why Do I Need Vehicle Signs?
In a busy city like Los Angeles, a car with a full vinyl vehicle wrap can generate a staggering 30,000 to 70,000 impressions a day. Even in the UK, a long-haul truck with a vinyl wrap will generate ten million impressions during the course of a year.
But unless your vehicle wrap is done to the most professional standards, you’ll only create a poor first impression which turns potential customers off. At the Sussex Sign Company our technicians are highly experienced, and they’ll ensure that you get the maximum return on your investment from this powerful form of mobile advertising.
If you’re interested in getting your vehicle wrapping done by the professionals, contact us via phone or email today and we can discuss implementing your car wrap design ideas with our fully integrated design, manufacture, installation and maintenance services.